1946 bitsa project

User avatar
SEDoan
Holder of a Nylon Anorak
Holder of a Nylon Anorak
Posts: 127
Joined: Mon Feb 15, 2021 2:29 am
Contact:

Re: 1946 bitsa project

Post by SEDoan »

I'm surprised "breather brackets" could generate so much interest - this next one should really stir the pot. :lol:

The girder was bent, not badly, but looking closer I was worried I wouldn't be able to straighten it. I know this is specialist work, and I'm not. However, given the expense and risk of sending it half way around the world during a pandemic winter, I thought it was worth a try. And the info might help others.

The upper triangle pivots are out of alignment, but that it is a simple twist.
20220101_135217.jpg
Clamped to a strongback and put in the press to take the twist out.
20220101_141709.jpg
Of course this kicked one leg forward causing a mis-aligned axle.
20220101_143527.jpg
That leg also had an S-bend near the dropout lug.
20220101_144300.jpg
To straighten the S-bend and align the axle meant the dropout had to be removed. The lugs are pinned. Locate both ends of the pin and drill from both ends through the lug. Melt the brass and knock off the lug - it takes a lot of heat.
20220102_180912.jpg
1937 Guzzi GTV, 1939 VH bitsa, 1947 VH, 1981 Guzzi Monza, 1983 Guzzi Lemans
User avatar
SEDoan
Holder of a Nylon Anorak
Holder of a Nylon Anorak
Posts: 127
Joined: Mon Feb 15, 2021 2:29 am
Contact:

Re: 1946 bitsa project

Post by SEDoan »

The fork tubes are easy to manipulate individually. I used heat and a close fitting steel pipe to straighten the S-bend. It is possible to lever with the pipe opposite the heat so the tube is not dimpled. With the upper fork clamped to the strongback the individual tubes can be pushed or pulled by hand cold - no heat needed. They bend at the lower pivot lug. Very little movement is required to align the 2 sides of the fork.
20220101_185637.jpg
Test fit the lug to make sure the fork is aligned for both front to back and length from lower pivot to axle. Replace the pins, check again and braze it up.
20220105_212218.jpg
20220106_110315.jpg
The assembled fork. Not the prettiest, but I think it will work.
20220106_110955.jpg
1937 Guzzi GTV, 1939 VH bitsa, 1947 VH, 1981 Guzzi Monza, 1983 Guzzi Lemans
User avatar
simon.holyfield
Holder of a Platinum Anorak
Holder of a Platinum Anorak
Posts: 4692
Joined: Mon Oct 17, 2011 11:16 pm
Location: Norfolk
Contact:

Re: 1946 bitsa project

Post by simon.holyfield »

Thanks for sharing, very interesting.

What did you heat it with?
cheers

Simes

'51 Square Four,
'58 Huntmaster,
'42 W/NG,
'30 Model A
https://ariel-square-four.blogspot.com
User avatar
SEDoan
Holder of a Nylon Anorak
Holder of a Nylon Anorak
Posts: 127
Joined: Mon Feb 15, 2021 2:29 am
Contact:

Re: 1946 bitsa project

Post by SEDoan »

Correction: Oxy/acetylene heating tip to separate the lug and re-braze it, and a standard torch tip to straighten the tubes and finish braze.
1937 Guzzi GTV, 1939 VH bitsa, 1947 VH, 1981 Guzzi Monza, 1983 Guzzi Lemans
User avatar
SEDoan
Holder of a Nylon Anorak
Holder of a Nylon Anorak
Posts: 127
Joined: Mon Feb 15, 2021 2:29 am
Contact:

Re: 1946 bitsa project

Post by SEDoan »

Here's the frame and fork together from a couple months ago:
20220124_181221.jpg
The rear engine plates were a mess - foot rest supports and mag platform brazed on and both plates badly bent because no spacer was used between them when tightening the foot rest tie-bolt.
20220310_171249.jpg
20220312_091254.jpg
20220326_192554.jpg
1937 Guzzi GTV, 1939 VH bitsa, 1947 VH, 1981 Guzzi Monza, 1983 Guzzi Lemans
Paul Slootheer
Holder of a Silver Anorak
Holder of a Silver Anorak
Posts: 823
Joined: Mon Jul 30, 2012 5:47 pm
Contact:

Re: 1946 bitsa project

Post by Paul Slootheer »

Great job Sean, well done!
User avatar
SEDoan
Holder of a Nylon Anorak
Holder of a Nylon Anorak
Posts: 127
Joined: Mon Feb 15, 2021 2:29 am
Contact:

Re: 1946 bitsa project

Post by SEDoan »

Thank you Paul.

Today I took most of the bicycle to the painter for a coat of black, but there were a few things to do first...

Didn't have enough good parts to restore the brakes so decided to make self-energizing brakes from Triumph Spitfire car rear shoes (cheap). They are about 1/8" too wide.
20220111_200849.jpg
20220312_082815.jpg
Treated the brake plate to a new stainless trim ring from club spares - thanks Allan!
20220312_082817.jpg
Had a few bits chromed:
20220328_204406.jpg
Welded and re-drilled some egg-shaped holes.
20220501_125247.jpg
1937 Guzzi GTV, 1939 VH bitsa, 1947 VH, 1981 Guzzi Monza, 1983 Guzzi Lemans
User avatar
SEDoan
Holder of a Nylon Anorak
Holder of a Nylon Anorak
Posts: 127
Joined: Mon Feb 15, 2021 2:29 am
Contact:

Re: 1946 bitsa project

Post by SEDoan »

Big time was spent on a cheap India made tank that didn't fit and has a long list of errors. (It is from an ebay seller VintageBikeUSA who advertised pictures of a well made tank and then sold a POS.)

New mounting pads were needed and they needed to raise the tank to clear the 500cc rocker boxes. Not pretty but seemed to work.
20220511_200601.jpg
20220511_184036.jpg
20220511_183800.jpg
Once the tank fit I could take the parts to the painter. I delivered them today - hurray!
20220512_065701.jpg
Looking forward to building the forks and wheels and having a roller.
1937 Guzzi GTV, 1939 VH bitsa, 1947 VH, 1981 Guzzi Monza, 1983 Guzzi Lemans
User avatar
SEDoan
Holder of a Nylon Anorak
Holder of a Nylon Anorak
Posts: 127
Joined: Mon Feb 15, 2021 2:29 am
Contact:

Re: 1946 bitsa project

Post by SEDoan »

The parts were painted more than a month ago, but it's been put on hold until some house projects are done.
20220614_172930.jpg
1937 Guzzi GTV, 1939 VH bitsa, 1947 VH, 1981 Guzzi Monza, 1983 Guzzi Lemans
JohnnyBeckett
Holder of a Golden Anorak
Holder of a Golden Anorak
Posts: 2381
Joined: Sat Jul 07, 2018 5:39 pm
Contact:

Re: 1946 bitsa project

Post by JohnnyBeckett »

hi , it is coming along very nice now keep up the good work 8-) :)
Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests