Carrier
-
- Holder of a Nylon Anorak
- Posts: 188
- Joined: Sun Oct 30, 2022 9:53 am
- Location: Nr Poole, Dorset
- Contact:
Carrier
Evening all,
Does anyone know of a supplier for the carrier p/n 5630-41?
If not, does the club have a works drawing?
Regards
Steve
Does anyone know of a supplier for the carrier p/n 5630-41?
If not, does the club have a works drawing?
Regards
Steve
-
- Holder of a Golden Anorak
- Posts: 2391
- Joined: Sat Jul 07, 2018 5:39 pm
- Contact:
Re: Carrier
hi have you been onto Drags or try john budgen he may have one
Re: Carrier
These guys have it on their site:
http://www.parkwoodproducts.co.uk/racks.html
http://www.parkwoodproducts.co.uk/racks.html
Ariel W/NG '40 "Bitzer", Triumph Thruxton '04, IZH-49 '56, Tempo Standard 150 '54.
-
- Holder of a Golden Anorak
- Posts: 2391
- Joined: Sat Jul 07, 2018 5:39 pm
- Contact:
Re: Carrier
hi parkwood is very good i see him at kempton park motorcycle autojumble i forgot about him i did put a post about him under supplies a while back on this forum
-
- Holder of a Nylon Anorak
- Posts: 188
- Joined: Sun Oct 30, 2022 9:53 am
- Location: Nr Poole, Dorset
- Contact:
Re: Carrier
Excellent, thank you very much for all your help.
Re: Carrier
Steve,
Parkwood are out of stock and according to them they are not expecting them for a number of months sadly
Adam
Parkwood are out of stock and according to them they are not expecting them for a number of months sadly
Adam
-
- Holder of a Golden Anorak
- Posts: 2391
- Joined: Sat Jul 07, 2018 5:39 pm
- Contact:
Re: Carrier
hi drags are saying they now have them in stock now according to the news letter today
Re: Carrier
I rang drags today as I am also looking for one and they don't have any, with none in the making either. They did say pop your info on the website in the pro-forma at the bottom of the carrier page to register your interest, maybe they will decide to produce some.
I would say they do not look overly difficult to produce a one off if you have a pipe bender, welder and if you had the measurements.
I am sure I saw a post on a website somewhere which had the measurements!? Will see if I can remember where as I would say i will need them too soon...
Adam
I would say they do not look overly difficult to produce a one off if you have a pipe bender, welder and if you had the measurements.
I am sure I saw a post on a website somewhere which had the measurements!? Will see if I can remember where as I would say i will need them too soon...
Adam
- simon.holyfield
- Holder of a Platinum Anorak
- Posts: 4705
- Joined: Mon Oct 17, 2011 11:16 pm
- Location: Norfolk
- Contact:
Re: Carrier
There are three posts on my blog showing how I made mine - the dimensions came from Vincent van Ginneke, on this very forum.
I used round bar, its easier to get the bends neat than using tube.
This is the first one:
https://ariel-square-four.blogspot.com/ ... k.html?m=0
Second one:
https://ariel-square-four.blogspot.com/ ... 2.html?m=0
Last one:
https://ariel-square-four.blogspot.com/ ... 3.html?m=0
I used round bar, its easier to get the bends neat than using tube.
This is the first one:
https://ariel-square-four.blogspot.com/ ... k.html?m=0
Second one:
https://ariel-square-four.blogspot.com/ ... 2.html?m=0
Last one:
https://ariel-square-four.blogspot.com/ ... 3.html?m=0
cheers
Simes
'51 Square Four,
'58 Huntmaster,
'42 W/NG,
'30 Model A
https://ariel-square-four.blogspot.com
Simes
'51 Square Four,
'58 Huntmaster,
'42 W/NG,
'30 Model A
https://ariel-square-four.blogspot.com
Re: Carrier
Simon, excellent! Everything we need to make one up
Thank you!
Adam
Thank you!
Adam
Who is online
Users browsing this forum: No registered users and 1 guest