More connecting rod bolt questions

Singles, twins and fours.
Post Reply
ann-marie.scott
Posts: 19
Joined: Fri Jul 29, 2022 11:40 pm
Contact:

More connecting rod bolt questions

Post by ann-marie.scott »

On the 58 square four that I am rebuilding, are the connecting rod bolts even something to worry about? These are a high grade bolt with low torque loading on a low powered low compression engine. Am I being overly cautious?
will_curry
Holder of a Silver Anorak
Holder of a Silver Anorak
Posts: 959
Joined: Thu Oct 08, 2015 12:56 am
Contact:

Re: More connecting rod bolt questions

Post by will_curry »

The bottom end of Square Fours is flimsy at best and, an egg-sucking lesson perhaps, the
oilways need to be completely cleaned out.

If you don't know anything of the engine's history a set of new rods from the club is good
insurance as a broken rod will wreck the crankcases at the very least.
ann-marie.scott
Posts: 19
Joined: Fri Jul 29, 2022 11:40 pm
Contact:

Re: More connecting rod bolt questions

Post by ann-marie.scott »

The impression I have is that the rods are fine as long as they have oil. Are old rods just false economy?
nevhunter
Holder of a Platinum Anorak
Holder of a Platinum Anorak
Posts: 5026
Joined: Tue May 10, 2011 9:42 am
Location: Victoria.. Australia.
Contact:

Re: More connecting rod bolt questions

Post by nevhunter »

Aluminium fatigues more than the usual steel rods. You have no way of knowing for sure how hard the motor has been used. Loss of oil to the rear LH rod due sludge is he most common failure. IF you know it's history and it's not done a lot of miles you could just do a cracktest and not ride it too hard. (High Revs). Some people are revheads and I wouldn't do it on a SQ4. Nev
User avatar
Roger Gwynn
Holder of a Golden Anorak
Holder of a Golden Anorak
Posts: 1113
Joined: Tue May 28, 2013 11:34 am
Location: Norwich, UK
Contact:

Re: More connecting rod bolt questions

Post by Roger Gwynn »

The aluminium will fatigue with use due to the strain of thrashing up and down thousands of times a minute. Over time this may cause failure of the rod, however I am hard pushed to remember an engine failure involving a broken rod that didn't show evidence of big end seizure. In other words the rods tend to break not due to the failure of the rod but a failure in the oil supply system, usually number 4 rod as it is furthest from the oil supply. If in any doubt I would replace the rods, an engine blow up will cost more than the rods and where can replacement cases be found?
Roger Gwynn, Membership Secretary, curator of the Machine Register and the works drawings. Director of Draganfly Motorcycles, Craven Equipment and Supreme Motorcycles mostly retired.
ann-marie.scott
Posts: 19
Joined: Fri Jul 29, 2022 11:40 pm
Contact:

Re: More connecting rod bolt questions

Post by ann-marie.scott »

Will I have to relieve the crankcases in order for the new rods to fit?
User avatar
paul.jameson
Holder of a Golden Anorak
Holder of a Golden Anorak
Posts: 2933
Joined: Wed Oct 12, 2011 3:04 pm
Location: Herefordshire
Contact:

Re: More connecting rod bolt questions

Post by paul.jameson »

No - I have never needed to.
Paul Jameson
35 LG (project), 37 RH500, 52 ex ISDT KHA, 54 KH(A), 75 Healey 1000/4.
Former Machine Registrar & Archivist, General Secretary and Single Spares Organiser (over a 25 year period).
Now Archivist (but not Machine Registrar), Gauges and Clocks Spares Organiser.
ann-marie.scott
Posts: 19
Joined: Fri Jul 29, 2022 11:40 pm
Contact:

Re: More connecting rod bolt questions

Post by ann-marie.scott »

Thanks for your help!
Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests