Search found 1100 matches
- Mon Jan 16, 2023 10:23 am
- Forum: W/NG Technical
- Topic: Tin chaincase gasket material
- Replies: 12
- Views: 1612
Re: Tin chaincase gasket material
The original was in cork but you will need a close grain cork sheet as the usual stuff sold for floor tiles etc will be too course to make small holes in. It is possible to buy sheet cork, model railway shops sell it for use as track underlay, though probably a bit thin. Alternatively run the case d...
- Sat Jan 14, 2023 10:07 pm
- Forum: W/NG General
- Topic: cable clips head stock
- Replies: 2
- Views: 770
Re: cable clips head stock
Look up the part number on the Draganfly site, most have the thread size listed.
- Sat Jan 14, 2023 3:19 pm
- Forum: Four stroke
- Topic: cylinder to head mating question - w/ng
- Replies: 22
- Views: 1226
Re: cylinder to head mating question - w/ng
Where are these chamfered edges? The seal is on the top of the spigot or the top of what would be a liner if there was one. There should be a small gap twixt the head and cylinder surfaces where the bolts go through. You may have a later cylinder and an early head. The diameter of the spigot was red...
- Fri Jan 13, 2023 11:40 am
- Forum: Main Chat Forum
- Topic: 1951 KH 500 Refurbishment
- Replies: 4
- Views: 424
Re: 1951 KH 500 Refurbishment
1952 models did not have chrome on the tank, which was dropped in February 1951, supposedly due to the lack of nickle caused by the Korean war which was, what would now be called false news. There is no mention of colour in the despatch books, looks like a Dulux colour!
- Thu Jan 12, 2023 9:39 am
- Forum: Four stroke
- Topic: 1957 Huntmaster tank knee pads
- Replies: 2
- Views: 198
Re: 1957 Huntmaster tank knee pads
Yup. They have a lip that 'hooks' over a plate fixed to the tank, the ally surrounds are just trapped between the knee grip and the tank. A great source of rot is water trapped behind the grips.
- Wed Jan 11, 2023 4:44 pm
- Forum: Four stroke
- Topic: Oil feed pipe to rockers leaking - WN/G advice needed
- Replies: 1
- Views: 134
Re: Oil feed pipe to rockers leaking - WN/G advice needed
Solder and 3/16 tube not 1/4. Can re-use fittings but need to clean them well first, brake cleaner, ultra-sonic bath, dishwasher et al. New fittings are available at Draganfly as well as pipe if you want to make or repair your own.
- Tue Jan 10, 2023 11:13 am
- Forum: Main Chat Forum
- Topic: Finding my first bike
- Replies: 2
- Views: 398
Re: Finding my first bike
It appears twice in the club's machine register, the good news is both times in the hands of well known club members, the bad news is that both entries are from the 80's. Engine and frame T 29966 T
- Tue Jan 10, 2023 10:12 am
- Forum: Four stroke
- Topic: Rear hub bearing lockring thread?
- Replies: 2
- Views: 145
Re: Rear hub bearing lockring thread?
There are very few lh threads on Ariels and none are wheel bearing lock rings
- Mon Jan 09, 2023 3:36 pm
- Forum: Four stroke
- Topic: Securing bolt or screw / lower chain guard
- Replies: 3
- Views: 190
Re: Securing bolt or screw / lower chain guard
Yes, it is case screw with Whit nut and no thread in the inner case. On Draganfly's web site under chainguards they helpfully list all the fastenings for each and every chainguard, no doubt in the vain hope that people will appreciate the time and effort spent in researching the parts and will buy p...
- Sat Jan 07, 2023 10:47 pm
- Forum: Electrics
- Topic: New 'Red Dot' Ammeters now available
- Replies: 10
- Views: 1264
Re: New 'Red Dot' Ammeters now available
This is a new item that has just been manufactured by Wassells so there should not be any delay in supply and many dealers will have them.