Search found 127 matches
- Thu Jan 26, 2023 6:46 pm
- Forum: W/NG Technical
- Topic: Got myself some tins - need some advice
- Replies: 4
- Views: 1223
Re: Got myself some tins - need some advice
Steve, the first plate is just a slightly off round disc which spreads the load of the 4 screws into the chaincase as it attaches to the engine case. I made one out of a piece of tin to fit. The second is the barrier between the dry clutch basket and plates to the wet chaincase. It has to be fitted ...
- Wed Jan 25, 2023 10:20 am
- Forum: Four stroke
- Topic: W/NG - front brake cable length, far too short
- Replies: 3
- Views: 305
Re: W/NG - front brake cable length, far too short
From the other post, the cables seem to be made to drawing, but for some reason wouldn't fit my application.
Maybe I have an unusual assembly of parts? Maybe the drawing is wrong? I had mine made a few inches longer but the inner to outer freeplay remain the same.
Regards
Adam
Maybe I have an unusual assembly of parts? Maybe the drawing is wrong? I had mine made a few inches longer but the inner to outer freeplay remain the same.
Regards
Adam
- Tue Jan 24, 2023 7:58 pm
- Forum: W/NG Technical
- Topic: Front brake cable source
- Replies: 16
- Views: 2566
Re: Front brake cable source
Thank you for all the help, I had one made by jj cables, looks decent quality and now should fit fine.
Thanks
Adam
Thanks
Adam
- Tue Jan 24, 2023 7:54 pm
- Forum: Four stroke
- Topic: W/NG - front brake cable length, far too short
- Replies: 3
- Views: 305
Re: W/NG - front brake cable length, far too short
Steve, I just had an issue with a brand new front brake cable being too short too on my wng its in the wng technical section. Mine was about 2 inches too short so I had one made by jj cables to my spec.
Adam
Adam
- Mon Jan 16, 2023 1:24 pm
- Forum: W/NG Technical
- Topic: Tin chaincase gasket material
- Replies: 12
- Views: 2053
Re: Tin chaincase gasket material
Thank you both for the response! I will give Russell motors a call when they open tomorrow, failing that will take a look in the local hobby store to see what I can get cork wise. I would like to try and seal it if I can, although will see about perhaps running without oil but i worry about wear to ...
- Mon Jan 16, 2023 6:10 am
- Forum: W/NG Technical
- Topic: Tin chaincase gasket material
- Replies: 12
- Views: 2053
Re: Tin chaincase gasket material
Johnny, sadly no luck with Geoff this time, he doesn't sell them
Many thanks
Adam
Many thanks
Adam
- Sun Jan 15, 2023 9:36 pm
- Forum: W/NG Technical
- Topic: Tin chaincase gasket material
- Replies: 12
- Views: 2053
Re: Tin chaincase gasket material
I haven't yet, but will send him a message now!
Thank you
Adam
Thank you
Adam
- Sun Jan 15, 2023 8:18 pm
- Forum: W/NG Technical
- Topic: Tin chaincase gasket material
- Replies: 12
- Views: 2053
Re: Tin chaincase gasket material
Thank you for the reply Johnny, but drags state no longer available, not even a back order message.
Thank you
Adam
Thank you
Adam
- Sun Jan 15, 2023 6:05 pm
- Forum: W/NG Technical
- Topic: Tin chaincase gasket material
- Replies: 12
- Views: 2053
Tin chaincase gasket material
Hi, Could anyone assist with what gasket material a 45 tin chaincase would be made of please? When I dismantled the inner clutch cover from the outer case there was quite a thick gasket material but I couldn't really tell what it was. I have tried using 4mm cork to emulate the original but it is too...
- Sun Jan 08, 2023 1:07 pm
- Forum: W/NG specific parts wanted or offered
- Topic: Last bits for my W/NG to find please
- Replies: 3
- Views: 1054
Re: Last bits for my W/NG to find please
Roger,
There is no information on my frame as it is after the last documented war department contract, so I guess nothing fitted would be incorrect!
Unless a tin timing case turns up i will be keeping it as an aluminium one for the time being,
Many thanks
Adam
There is no information on my frame as it is after the last documented war department contract, so I guess nothing fitted would be incorrect!
Unless a tin timing case turns up i will be keeping it as an aluminium one for the time being,
Many thanks
Adam