Search found 579 matches
- Sun Oct 22, 2023 1:23 pm
- Forum: Four stroke
- Topic: Using a table lift
- Replies: 6
- Views: 496
Re: Using a table lift
Hi You can, but it could be pretty precarious depending on how large the table lift is. Best to make some wooden frame tube cradles so as to support the frame clear of the prop stand lug, exhaust etc. and ensure it goes up perpendicular. Personally, if I didn't have a bike lift I'd do it on the cent...
- Thu Oct 19, 2023 3:03 pm
- Forum: Main Chat Forum
- Topic: Ariel Riding and Fixing 2023
- Replies: 300
- Views: 21870
Re: Ariel Riding and Fixing 2023
Hi I was wondering what could have caused a failure such as this and I think you have the answer in the, non standard, cylinder base gasket. In my opinion, leather will compress in use due to the heat cycling of the engine and the barrel nuts will lose torque. Unless you are going to engage in a str...
- Sun Oct 15, 2023 7:42 am
- Forum: Main Chat Forum
- Topic: Ariel club Slovakia 2024 calendar
- Replies: 24
- Views: 2504
Re: Ariel club Slovakia 2024 calendar
Hi
Love the maritime braking 'upgrade' on the FH pictured at Queensferry
Regards Mick
Love the maritime braking 'upgrade' on the FH pictured at Queensferry
Regards Mick
- Tue Oct 10, 2023 7:06 am
- Forum: Electrics
- Topic: Ammeter not reading.
- Replies: 19
- Views: 2519
Re: Ammeter not reading.
Hi If there's nothing obvious when you look at the wiring I'd start by checking out the ammeter. Disconnect the wires from the terminal post, (making a note of where they are fitted), and tape the ends to avoid accidental contact / arcing. Place the probes from a multimeter, set to resistance on the...
- Sun Oct 01, 2023 6:27 am
- Forum: Four stroke
- Topic: Oil weep from feed pipe nut
- Replies: 21
- Views: 1214
Re: Oil weep from feed pipe nut
Hi
Yes, that's the correct nipple for a 5/16", (8mm), pipe. In fact the picture seems to have been sourced from The Green Spark Plug Companies web site.
Regards Mick
Yes, that's the correct nipple for a 5/16", (8mm), pipe. In fact the picture seems to have been sourced from The Green Spark Plug Companies web site.
Regards Mick
- Sat Sep 30, 2023 6:33 am
- Forum: Four stroke
- Topic: Oil weep from feed pipe nut
- Replies: 21
- Views: 1214
Re: Oil weep from feed pipe nut
Hi I'd be very careful if either silver soldering or annealing the pipes, you need to ensure absolute cleanliness internally, heating to 'red' hot will carbonise any oil in the pipe which may then flake off in use and restrict oil flow downstream. I don't really see much point in annealing the pipe ...
- Wed Sep 27, 2023 7:41 am
- Forum: Four stroke
- Topic: Oil weep from feed pipe nut
- Replies: 21
- Views: 1214
Re: Oil weep from feed pipe nut
Hi In my experience the most likely cause of a weep will be damage to the mating surfaces of the union and pipe nipple. If you're going to strip them for investigation I'd replace the nipple and union as a matter of course. The nipple is just soft soldered on and are available here: https://www.gspa...
- Tue Sep 26, 2023 6:47 am
- Forum: For sale/wanted - Parts, and those bits and bobs
- Topic: dual seat for sq4g mk2
- Replies: 5
- Views: 687
Re: dual seat for sq4g mk2
Hi
I sourced a brand new dual seat for my 58 FH restoration from https://www.rk-leighton.co.uk/ Excellent quality and fit.
Regards Mick
I sourced a brand new dual seat for my 58 FH restoration from https://www.rk-leighton.co.uk/ Excellent quality and fit.
Regards Mick
- Mon Sep 25, 2023 6:00 am
- Forum: Four stroke
- Topic: Vb600 gearbox query. GB5
- Replies: 5
- Views: 426
Re: Vb600 gearbox query. GB5
Hi It's fitted from the outside, onto the indicator shaft and into the recess in the outer cover, a smear of Vaseline helps. Don't bother fitting it before you fit the outer cover as the action of sleeving the cover over the indicator shaft more often than not pushes the seal out of the recess. Rega...
- Fri Sep 22, 2023 7:59 am
- Forum: Ariel Talk
- Topic: Magnetic particle pickups.
- Replies: 10
- Views: 1085
Re: Magnetic particle pickups.
Hi All engines 'make' metal, the degree, time and quantity is indicative of the state of 'health' of the engine. After an overhaul metal will be produced as a product of parts bedding in, during normal running ingested road debris can remove metal as it makes it's way to the sump / oil tank, interna...