Johnny's comment echoes my question about the use of seals, but Mike's post has answered it precisely. Thank you both.
The seals are designed to allow some oil to pass to provide lubrication, which sounds right.
Search found 335 matches
- Sat Feb 25, 2023 10:50 am
- Forum: Ariel Talk
- Topic: Square four overhaul/valve guide seals etc.
- Replies: 22
- Views: 2252
- Fri Feb 24, 2023 4:39 pm
- Forum: Four stroke
- Topic: Sq4 MkI- new life
- Replies: 76
- Views: 4030
Re: Sq4 MkI- new life
I've seen a picture somewhere on this forum. I'll try to find it later, if I get a chance. Viewing the OPRV from the 'open end,' imagine fitting the ball and spring and split pit. Whilst the split pin legs are still straight, insert a small screwdriver or whatever between the legs inside the hole in...
- Fri Feb 24, 2023 3:26 pm
- Forum: Four stroke
- Topic: Sq4 MkI- new life
- Replies: 76
- Views: 4030
Re: Sq4 MkI- new life
Can you introduce some oil to lubricate it and try again? I do wonder if using just pressurised air is a reliable test. Air is not exactly viscous and may behave differently to hot or cold oil. Also, there will be friction inside the OPRV where the spring can kink and contact the body. Perhaps if o...
- Fri Feb 24, 2023 2:54 pm
- Forum: Four stroke
- Topic: Sq4 MkI- new life
- Replies: 76
- Views: 4030
Re: Sq4 MkI- new life
So if that is the case on a 4, how do they regulate a different pressure with the same valve? I've read somewhere that stretching the spring (yes, really!) will increase the amount of preload and thus the force acting on the ball when it is fitted into the OPRV.* On Norton twins, the (much larger) ...
- Fri Feb 24, 2023 11:09 am
- Forum: Ariel Talk
- Topic: Square four overhaul/valve guide seals etc.
- Replies: 22
- Views: 2252
Re: Square four overhaul/valve guide seals etc.
I'll have a word with my retired machinist friend. He'll tell me if he has the tools for the job.
Looking forward to your reports on carb and ignition.
Allan.
Looking forward to your reports on carb and ignition.
Allan.
- Thu Feb 23, 2023 5:33 pm
- Forum: Ariel Talk
- Topic: Square four overhaul/valve guide seals etc.
- Replies: 22
- Views: 2252
Re: Square four overhaul/valve guide seals etc.
Hi Frank, I've realised one important fact. The o.d. of the valve guide is 14.1 mm. The i.d. of the inner valve spring is 16.3 mm (quick measurements with a caliper.) Therefore, there is no room for a seal around the top of the guide. The tops of the guides will need to be reduced in diameter so tha...
- Thu Feb 23, 2023 12:26 pm
- Forum: Ariel Talk
- Topic: Square four overhaul/valve guide seals etc.
- Replies: 22
- Views: 2252
Re: Square four overhaul/valve guide seals etc.
Ah, I see, that explains the need for the special cutter. I've found VGS' website now https://vgs2cv.be/en/tool-klep-seal-AZ-M4-p531340456 and the special cutter, as shown in the video. I'm hoping that I will find some suitable seals which will be the right size for the Square Four without the need ...
- Thu Feb 23, 2023 9:00 am
- Forum: Four stroke
- Topic: Square 4 Valve Guide Shroud p/n 549-55
- Replies: 10
- Views: 518
Re: Square 4 Valve Guide Shroud p/n 549-55
They seem to be a bit erratic, in my experience, Paul. Often, I have received the confirmation after I've received the order. Every now and again, I'll receive an emailed invoice for something that I ordered (and received) weeks previously.
Not the end of the world, I suppose!
Not the end of the world, I suppose!
- Thu Feb 23, 2023 8:55 am
- Forum: Ariel Talk
- Topic: Square four overhaul/valve guide seals etc.
- Replies: 22
- Views: 2252
Re: Square four overhaul/valve guide seals etc.
That's the tool for the job, for sure. An easy task for someone with my skill set.... I've tried googling VGS and so far, have drawn a blank. I'm also trying a different approach, by trying to find valve stem seals which are the correct size for a Square Four. (I've been assuming that the existing g...
- Wed Feb 22, 2023 5:28 pm
- Forum: Ariel Talk
- Topic: Square four overhaul/valve guide seals etc.
- Replies: 22
- Views: 2252
Re: Square four overhaul/valve guide seals etc.
Thanks, Markus.
Did you have to machine the guides so that the Volvo seals would fit? If so, would you please let me know how this was done?
Allan.
Did you have to machine the guides so that the Volvo seals would fit? If so, would you please let me know how this was done?
Allan.