Search found 106 matches
- Mon Dec 31, 2018 9:11 am
- Forum: Ariel Talk
- Topic: Alloy brake plate for type 3 telescopic forks 46-55
- Replies: 2
- Views: 1231
Alloy brake plate for type 3 telescopic forks 46-55
For the start of the New Year I'm sharing my progress on my latest 500 cc single special which may be of interest. The photos show the alloy brake plate I've made to substitute for the standard pressed steel version. I'm not sure if this has been attempted before but this is my version. The material...
- Thu Jul 05, 2018 3:50 pm
- Forum: Ariel Talk
- Topic: TT carb on 500 single
- Replies: 21
- Views: 9520
Re: TT carb on 500 single
Thanks John, after fruitless conversations with most of the employees at John Deere I need some more info if you have it - or better still the outlet where you obtained yours. Engine type or anything.
Regards
Rob
Regards
Rob
- Thu Jul 05, 2018 3:13 pm
- Forum: Four stroke
- Topic: Rear wheel sprockets
- Replies: 7
- Views: 2602
Re: Rear wheel sprockets
Mine are 0.258 inch dia. Using a piece of round bar which was a tight fit in the hole and measured with a vernier.
Sprocket fitting - Q recess on the inside or outside?
Rob
Sprocket fitting - Q recess on the inside or outside?
Rob
- Wed Jul 04, 2018 9:54 pm
- Forum: Four stroke
- Topic: Rear wheel sprockets
- Replies: 7
- Views: 2602
Re: Rear wheel sprockets
How about loose fitting the bolts and tapping the sprocket anticlockwise (in the direction of drive) and when you are satisfied you've taken up any slack - tighten up.
Just about to fit one so I will check to see how mine goes. My sprocket was ebay used so Ill check the hole dia's
Cheers Rob
Just about to fit one so I will check to see how mine goes. My sprocket was ebay used so Ill check the hole dia's
Cheers Rob
- Wed Jul 04, 2018 9:46 pm
- Forum: Ariel Talk
- Topic: TT carb on 500 single
- Replies: 21
- Views: 9520
Re: TT carb on 500 single
Nev, Agreed on the grease my mistake was being too confident with the setup and not greasing regularly. I did use high temp grease. I remember seeing excess carbon deposits on the exhaust side when stripping the exhaust valve guide but could also have been to my lack of regular greasing. I did have ...
- Tue Jun 26, 2018 4:31 pm
- Forum: Ariel Talk
- Topic: TT carb on 500 single
- Replies: 21
- Views: 9520
Re: TT carb on 500 single
Progress on the oil mist conversion for inlet and exhaust open valve singles which might be of interest. The prospect of some form of restrictor for the oil mist line is a distinct possibility for the future . Can't test at the moment waiting for the return of the overhauled magneto. Short term usin...
- Tue Jun 26, 2018 3:50 pm
- Forum: Forum Help
- Topic: stuck in outbox - personal messages
- Replies: 3
- Views: 6497
Re: stuck in outbox - personal messages
Thanks Dave have only ever sent 5 total as private, However I thinks Simes has it . If its a private mail then the recepient won't have had chance to read. I did delete the original messages and started again with the same effect waiting in Outbox read to view. Thanks for the replies both of you ver...
- Tue Jun 26, 2018 10:33 am
- Forum: Four stroke
- Topic: 1"spacer for VB carb
- Replies: 1
- Views: 942
Re: 1"spacer for VB carb
Made one from aluminium bar with a deep undercut allowing the studs to be exposed. 1/4 inch flanges both ends. 1 inch length is the max to allow a 389 1 1/8 amal to fit with bellmouth without touching the oil tank.
- Tue Jun 26, 2018 10:26 am
- Forum: Four stroke
- Topic: Morgo plunger pump for singles
- Replies: 17
- Views: 5416
Re: Morgo plunger pump for singles
I fitted one - no issues
- Tue Jun 26, 2018 9:56 am
- Forum: Forum Help
- Topic: stuck in outbox - personal messages
- Replies: 3
- Views: 6497
stuck in outbox - personal messages
Hi.
I have 2 messages that seem to be stuck in outbox - personal messages can't find any way out to send. Or does it take a little time to send? Thanks
Rob
I have 2 messages that seem to be stuck in outbox - personal messages can't find any way out to send. Or does it take a little time to send? Thanks
Rob