Search found 115 matches
- Thu May 30, 2024 12:26 pm
- Forum: Ariel Talk
- Topic: 1930 LF
- Replies: 107
- Views: 17609
Re: 1930 LF
After last Saturdays experiences I decided to give the fuel system a little more attention. Namely, drain out all the fuel - it was a bit on the "brown" side . Removed the carburettor float chamber, took out the float itself and lapped the float needle onto it's seat with some fine grindin...
- Sat May 25, 2024 8:03 pm
- Forum: Ariel Talk
- Topic: 1930 LF
- Replies: 107
- Views: 17609
Re: 1930 LF
Would not run, no spark, found that the points had closed up. Adjust the points find that the timing had slipped a little. Re-time the ignition, find muck in the fuel, clean out the lines. Took it to Cassington and someone else got it going, seems I wasn't kicking it hard enough (I am waiting on a r...
- Sat May 25, 2024 7:45 pm
- Forum: Main Chat Forum
- Topic: Ariel day in Oxfordshire
- Replies: 9
- Views: 755
Re: Ariel day in Oxfordshire
More Ariels at Cassington.
- Sat May 25, 2024 7:33 pm
- Forum: Main Chat Forum
- Topic: Ariel day in Oxfordshire
- Replies: 9
- Views: 755
Re: Ariel day in Oxfordshire
Some Ariels at Cassington
[attachment=0]IMG_20240525_104204358~2.jpg[/attachment- Tue May 14, 2024 6:35 pm
- Forum: Ariel Talk
- Topic: 1930 LF
- Replies: 107
- Views: 17609
Re: 1930 LF
In order get the taper correct I looked on line for 1:10 taper reamer, found one, ordered it. It proved to be not very expensive, only there proved to be a reason for that, despite being marked 1:10, it wasn't. More searching found another, rather more expensive but that least it was the correct tap...
- Fri May 10, 2024 2:37 pm
- Forum: Ariel Talk
- Topic: 1930 LF
- Replies: 107
- Views: 17609
- Thu May 09, 2024 2:00 pm
- Forum: Ariel Talk
- Topic: 1930 LF
- Replies: 107
- Views: 17609
Re: 1930 LF
Reducing the boss and thinning the teeth (they were a little too wide as supplied) was simple enough, however cutting the taper to suit the dynamo shaft took a little more trouble. Cutting an internal taper in it’s self is easy enough by settling over the lathe’s top slide, but getting it wrong is j...
- Tue May 07, 2024 3:48 pm
- Forum: Ariel Talk
- Topic: 1930 LF
- Replies: 107
- Views: 17609
Re: 1930 LF
The 14 tooth sprocket has arrived, before it can be fitted it will need a fair bit of machining. That is the teeth "thinned" to suit the drive chain. the boss reduced in size and length and finally taper board to suit the dynamo input shaft. IMG_20240507_145134772.jpg However trying to hol...
- Mon May 06, 2024 3:28 pm
- Forum: Ariel Talk
- Topic: 1930 LF
- Replies: 107
- Views: 17609
Re: 1930 LF
The "Smart Diode" has arrived, it's not very large, could possibly be fitted inside the dynamo end cover. However I have placed inside the headlight shell fixed to the original "cut-out" bracket. IMG_20240503_174626621.jpg Still not much in the way of voltage coming out of the dy...
- Thu May 02, 2024 3:49 pm
- Forum: Ariel Talk
- Topic: 1930 LF
- Replies: 107
- Views: 17609
Re: 1930 LF
I have removed the third brush and wired the dynamo field coil directly across the it's output, it is now operating as a simple unregulated generator. As to the cut-out I have ordered a "smart diode" which will prevent any "back current" flowing into the dynamo. This device is sa...