Search found 36 matches
- Sat Apr 29, 2023 4:12 pm
- Forum: Main Chat Forum
- Topic: con rod assembly oil
- Replies: 8
- Views: 484
Re: con rod assembly oil
Many thanks again for all your replies they have been most helpful
- Thu Apr 27, 2023 1:50 pm
- Forum: Main Chat Forum
- Topic: con rod assembly oil
- Replies: 8
- Views: 484
Re: con rod assembly oil
What can you use it for , i have seen the blurb on the internet .
Or what don't you use it for
Many thanks
Or what don't you use it for
Many thanks
- Thu Apr 27, 2023 1:21 pm
- Forum: Main Chat Forum
- Topic: con rod assembly oil
- Replies: 8
- Views: 484
Re: con rod assembly oil
Thanks were would i get some from
- Thu Apr 27, 2023 9:50 am
- Forum: Main Chat Forum
- Topic: con rod assembly oil
- Replies: 8
- Views: 484
con rod assembly oil
I bought some rods from the club a while ago but did not receive any of the oil .for the reassembly. I have been in contact with Iron horse and they only supply it with new Rods they sell The RODS i bought were oversize and were the last ones left , i purchased these as nobody knew when the next bat...
- Fri Oct 16, 2020 9:31 am
- Forum: Four stroke
- Topic: square 4 carb conversion
- Replies: 10
- Views: 2958
Re: square 4 carb conversion
Thank you what is the script with the air filter mine has none
- Thu Oct 15, 2020 4:15 pm
- Forum: Four stroke
- Topic: square 4 twin pipe alloy motor
- Replies: 2
- Views: 981
Re: square 4 twin pipe alloy motor
Dragonfly mention in there fact sheet that the timing side journal is 1.250.
I am not a mechanic or an engineer i am trying to pass on the information it also mentions big end eye diameter would this be correct
I am not a mechanic or an engineer i am trying to pass on the information it also mentions big end eye diameter would this be correct
- Thu Oct 15, 2020 1:43 pm
- Forum: Four stroke
- Topic: square 4 twin pipe alloy motor
- Replies: 2
- Views: 981
square 4 twin pipe alloy motor
Could anybody please tell me the standard crank size for a 1952 twin pipe alloy motor .The engineer has asked what the sizes they are as standard I have bought new rods and shells from the club and now the job is about to begin on the engine as the rolling chassis has been done for some time but cov...
- Tue Oct 06, 2020 10:50 am
- Forum: Four stroke
- Topic: square 4 carb conversion
- Replies: 8
- Views: 2134
Re: square 4 carb conversion
Thanks for everyone taking the time to reply this forum as a whole has been absolutely fantastic i have asked some really dumb questions and have received positive answers to all
- Tue Oct 06, 2020 7:52 am
- Forum: Four stroke
- Topic: square 4 carb conversion
- Replies: 10
- Views: 2958
Re: square 4 carb conversion
Many thanks i will tyr the solex and if i have any problems i will get in contact.
i have had it ultrasonic cleaned so i will see how i get on ,is there a set up procedure in the manual
i have had it ultrasonic cleaned so i will see how i get on ,is there a set up procedure in the manual
- Mon Oct 05, 2020 4:41 pm
- Forum: Four stroke
- Topic: square 4 carb conversion
- Replies: 10
- Views: 2958
square 4 carb conversion
I have been informed by dragonfly that they do not do the concentric conversion for my square 4 which is a twin pipe alloy engine 1952 in a 1956 rolling chassis .
Has anybody got any idea if this can be sorted or can i get a gasket set for the solex
many thanks
Bill Shortall
Has anybody got any idea if this can be sorted or can i get a gasket set for the solex
many thanks
Bill Shortall