Search found 1085 matches
- Wed Mar 27, 2024 10:23 am
- Forum: Two stroke
- Topic: ariel leader side panel screws .
- Replies: 2
- Views: 103
Re: ariel leader side panel screws .
Measure the diameter of the screw x UNF
- Thu Mar 21, 2024 9:39 pm
- Forum: Four stroke
- Topic: Ariel ng 1936/Carburettor Enquiries
- Replies: 4
- Views: 220
Re: Ariel ng 1936/Carburettor Enquiries
If the carb leaks when the engine is stopped, which is what I assume you mean, then either the float needle is not seating correctly or the float chamber is at the wrong height, which is a common problem and why these carbs are also known as 'old leaky'. An additional washer between the float chambe...
- Wed Mar 20, 2024 10:33 pm
- Forum: Ariel Talk
- Topic: NH350 piston ring size.
- Replies: 4
- Views: 155
Re: NH350 piston ring size.
You can gap +.40 rings to suit as long as they are conventional rings, not multi piece Cords type
- Wed Mar 20, 2024 11:03 am
- Forum: Four stroke
- Topic: ba clutch adjustment
- Replies: 5
- Views: 152
Re: ba clutch adjustment
You can easily check the dimensions of the clutch cable against those given on your invoice as 6460-33 Cable 48 1/4″ – 52 1/4″, to make sure that you been sent the right one. The correct adjuster has the recess for the cable ferule at the threaded end, not the hex end so the adjuster goes in from th...
- Tue Mar 19, 2024 11:36 am
- Forum: Main Chat Forum
- Topic: Scottish Bike Show - some Ariels
- Replies: 6
- Views: 279
Re: Scottish Bike Show - some Ariels
The 200 Arrow includes one of the more inaccurate potted histories of Ariel, worse than most auctioneers and that is saying something.
- Sun Mar 17, 2024 7:49 pm
- Forum: Ariel Talk
- Topic: '39 Sq4 exhaust conundrum
- Replies: 7
- Views: 197
Re: '39 Sq4 exhaust conundrum
It is one of those undocumented features, you have to trim some fins, this is correct and original!
- Tue Mar 12, 2024 3:42 pm
- Forum: Four stroke
- Topic: 1938 NH rear mudguard hole.
- Replies: 3
- Views: 132
Re: 1938 NH rear mudguard hole.
Correct, not original, reflector not fitted until1953, dropped in 1955 as incorporated into the 564 tail light
- Tue Mar 12, 2024 1:46 pm
- Forum: For sale/wanted - Bikes
- Topic: Benelli W/NG
- Replies: 0
- Views: 139
Benelli W/NG
I have just identified this fine machine as a post war conversion of a W/NG by Benelli, although there were others I think. It is currently languishing at Llanivet motors should anyone fancy a curio. There was an article about them in Cheval by JM in October 2012. I have a few more pics if anyone in...
- Sun Mar 10, 2024 10:13 am
- Forum: Four stroke
- Topic: Noisy VH engine - Roller mains
- Replies: 14
- Views: 376
Re: Noisy VH engine - Roller mains
Simon - Your are correct about the FH, it is a long time since I worked on one but when the price of lipped roller bearings for SQ4 went through the roof I talked to a tech guy at a bearing specialist who told me that the lip was not there as a thrust face and if the end float was controlled by othe...
- Sat Mar 09, 2024 6:25 pm
- Forum: Four stroke
- Topic: Noisy VH engine - Roller mains
- Replies: 14
- Views: 376
Re: Noisy VH engine - Roller mains
Not good to use the lips on rollers for end thrust they are not designed to do that, whereas ball races are. Apparently the lips are intended to act as a sort of safety net.